The Sketcher 1. This is a test
2. While in sketch mode, the number displayed to the right of the cursor defines the sketch element`s exact size. Therefore, there is no need to add a dimension to set the dimensional value.
3. If a geometric entity or a dimension is displayed in red, this implies that it is:
4. In order to create two-dimensional geometry such as lines, arcs, and rectangles, what mode should SOLIDWORKS be in?
5. The Power Trim tool can be used to extend a line to a target point.
Sketched Features 6. To create a closed Loft Feature, you must select all of the sketch sections, then select the first sketch again to define it as the start and end sketch.
7. What is the minimum number of sketches needed to create a simple Sweep feature?
8. Which end condition of an Extruded Boss is used to add an equal amount of material to both sides of the sketch plane?
9. Which of the following features is an applied feature, meaning that it is not defined by one or more sketches?
10. A loft feature can be created from a single 3D sketch.
Applied Features 11. You can select a planar face as the reference plane for mirroring a feature.
12. What group box in the Hole Wizard PropertyManager should you use if you want to add custom hole parameters for later use?
13. When using the Hole Wizard feature, it is only possible to create one hole.
14. Components are the building blocks of parts.
15. The View Orientation window appears by pressing the __________ key on the keyboard.
Parts 16. When you create a design table, the toolbars are changed and an embedded Excel application is started.
17. When modifying a dimension, you can specify which configuration(s) you want the modified dimension to apply to.
18. Using the __________ option, you can change the state of a model back to where a particular feature or features weren`t yet created.
19. Configurations you want to control with a design table must be defined before creating the design table.
20. After you create a design table, an Excel icon is displayed in the ConfigurationManager Tree which implies that the design table is driving the configuration.
Assemblies 21. You can apply the Tangent Mate between a flat face and a sphere.
22. When creating an Exploded View, you can move multiple components at the same time in a single step.
23. Which of the following is available for Assembly files but not for Part files?
24. The (f) in front of the first component listed in the Feature Manager Tree indicates:
25. You cannot apply mates between the face of a model and a reference plane.
Views 26. The Runout tolerances are combination symbols that can control location, orientation, and form simultaneously.
27. For the figure shown, a Positional tolerance is applied to a slotted feature in an alignment plate. Based on this information, select the statement that is NOT correct:
28. Which of the following curve features easily allows you to manually enter data points, as well as import them from an ASCII file?
29. A Bill of Materials created in a drawing cannot be exported as an excel document.
30. Which one of the following statements is not correct about Balloons?
Dimensions, Etc. 31. You can not add tolerances or notes to driven dimensions.
32. To save a Custom Sheet Format you should choose ______ from the File Drop Down Menu.
33. If there are concentric circles, then it is recommended that you apply the center mark to the ______ circle.
34. You can only use the default configuration of an assembly to drive a Bill of Materials.
35. A Bill of Materials can only be created in the drawings of part files.
Advanced Parts 36. A parting line is typically created based on:
37. The position of the snap hook can be specified by going to the...
38. When creating a 3D sketch, what button on the keyboard is used to change the active orientation or sketch plane?
39. The order in which the snap hook and snap groove are created does not matter.
40. The Split feature can be used to ______.
41. To create a Center Line Loft, the center line must intersect each profile and connect points from each profile together.
42. Hold Line Fillets are a type of Face Fillet.
Advanced Assemblies 43. External references are a side effect of creating:
44. Using SOLIDWORKS Explorer, you can determine what assembly a part file is used in by going to:
45. You cannot make changes at the part level while working in an assembly.
46. When creating a new configuration, you always have to give it a unique name, description, and comment.
47. Deleting component folders will also delete the components.
48. Assembly Features cannot be propagated to the individual part files of the components in which they affect.
49. The Width Mate:
Sheet Metal 50. The first step in creating a new sheet metal part is to create an Edge Flange.
51. You can use the sheet metal Corner Trim option to change the part in both its flattened and folded state.
52. The Rip feature is generally used to ________.
53. When creating a sketch for a sheet metal Base Flange, it`s important to break off any sharp corners with sketch fillets.
54. The Corner Trim feature can only be used on the flat pattern of a sheet metal part.
55. Forming tools can be found in the...
56. In order to select multiple edges for an Edge Flange they must be in contact.
SimulationXpress 57. Which of the following is NOT a valid SimulationXpress result?
58. You can use SimulationXpress to perform an analysis on a part with a custom material.
59. If you use a 4000lbs load, choose the Per Item option, and select two faces to apply the load, SimulationXpress applies a total load of 8000lbs.
60. You can apply __________ restraints or fixtures in SimulationXpress.
61. If you have a book shelf that you plan to put 25 lbs on, but the shelf will actually hold 100 lbs before it breaks, the shelf would have a factor of safety of:
